Hantek DSO4204C Digital Oscilloscope 200MHz 4Channels Bandwidth 1GSas Waveform Generator

€468.69
Tax excluded

Hantek DSO4204C Digital Oscilloscope 200MHz 4Channels Bandwidth 1GSa/s Waveform Generator

Chipsetpro.com

Chipsetpro.com

Quantity
Delivery will take 14-28 days

Features:

1.4 Channel Digital Oscilloscope + Arbitrary/Function Waveform Generator + Synchronizing Signal + External Trigger;

2.The Keys for osilloscope and waveform generator is seperated for convenient to operate it simultaneously;

3.Large and clear display (7 inch 64K color LCD display, Resolution 800x480), more clear and realistic waveform;

4.Oscilloscope: 1GSa/s Sample Rate, 200/100/70MHz Bandwidth, more than 20 kinds of auto measurement functions;

5.Powerful Trigger Function: Edge, Video, Pulse, Slope, Over time, Alternative;

6.Arbitrary/Function Waveform Generator: 25MHz, 12 bits resolution, 200MHz DDS, Arbitrary wave/square wave/sine wave/triangle 7.wave/trapezoidal wave/pulse wave/DC is easy to simulate transducer.

8.Support SD card, VGA function (optional);

9.Integrated USB Host, Support USB disk storage, USB interface/SD card system update.

Specifications:

Model DSO4204C

Oscilloscope

Sample Rate Sampling Rate Range: 1GSa/s

Equivalent Sample Rate: 25GSa/s

Acquisition Modes

Normal Normal data only

Peak Detect High-frequency and randon glith capture

Average Wavefom Average, selectable 4,8,16,32,64,128

Inputs

Inputs Coupling AC, DC, GND

Inpits Impendance 1MO2% ?20pF3pF

Probe Attenuation 1X, 10X

Supported Probe Attenuation Factor 1X, 10X, 100X, 1000X

Maximum Input Voltage CAT I and CAT II: 300VRMS (10)

CAT III: 150VRMS(1);

Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.

Horizontal

Sample Rate Range 1GS/s

Waveform Interpolation (sin x)/x

Record Length 40K

SEC/DIV Range 2ns/div to 40s/div 4ns/div to 40s/div

Sample Rate and 50ppm(at over any =1ms time interval)

Delay Time Accuracy

Position Range 2ns/div to 10ns/div; 20ns/div to 80us/div; (-8div x s/div) to 40ms;

(-4div x s/div) to 20ms; 200us/div to 40s/div; (-8div x s/div) to 400s

Delta Time Measurement Accuracy

(Full Bandwidth) Single-shot, Normal mode: (1 sample interval +100ppm reading + 0.6ns);

>16 averages: (1 sample interval + 100ppm reading + 0.4ns);

Sample interval = s/div 200

Vertical

Vertical Resolution 8-bit resolution, all channel sampled simultaneously

Position Range 2mV/div to 10V/div

Bandwidth 200MHz 100MHz 70MHz

Rise Time at BNC( typical) 1.8ns 3.5ns 5ns

Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled 2mV/div to 20mV/div, 400mV; 50mV/div to 200mV/div, 1V

500mV/div to 2V/div, 40V; 5V/div, 50V

Math +, -, *, /, FFT

FFT Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman;

1024 sample point

Bandwidth Limit 20MHz

Low Frequency Response (-3db) =10Hz at BNC

DC Gain Accuracy 3% for Normal or Average acquisition mode, 5V/div to 10mV/div;

4% for Normal or Average acquisition mode, 5mV/div to 2mV/div

DC Measurement Accuracy,

Average Acquisition Mode When vertical displacement is zero, and N =16: (3% reading + 0.1div + 1mV) only 10mV/div or greater is selected;

When vertical displacement is not zero, and N=16: [3% (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div

Volts Measurement Repeatability, Average Acquisition Mode Delta volts between any two averages of =16 waveforms acquired under same setup and ambient conditions

Trigger System

Trigger Types Edge, Video, Pulse, Slope, Over time, Alternative

Trigger Source CH1, CH2, EXT, EXT/5, AC Line

Trigger Modes Auto, Normal, Single

Coupling Type DC, AC, Noise Reject, HF Reject, LF Reject

Trigger Sensitivity

(Edge Trigger Type) DC(CH1,CH2):

1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;

DC(EXT):

200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;

DC(EXT/5):

1V from DC to 100MHz;1.75V from 100MHz to 200MHz;

AC: Attenuates signals below 10Hz;

HF Reject: Attenuates signals above 80kHz;

LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz

Trigger Level Range CH1/CH2: 8 divisions from center of screen;

EXT: 1.2V;

EXT/5:6V

Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times =20ns CH1/CH2: 0.2div volts/div within 4 divisions from center of screen;

EXT: (6% of setting + 40mV);

EXT/5: (6% of setting + 200mV);

Set Level to 50%(typical) Operates with input signals =50Hz

Video Trigger

Video Trigger Type CH1, CH2: Peak-to-peak amplitude of 2 divisions;

EXT: 400mV;

EXT/5: 2V

Signal Formats and Field Rates, Video Trigger Type Supports NTSC, PAL and SECAM broadcast systems for any field or any line

Holdoff Range 100ns ~ 10s

Pulse Width Trigger

Pulse Width Trigger Mode Trigger when (< , >, = , or ?); Positive pulse or Negative pulse

Pulse Width Trigger Point Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.

Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.

Less than: The trigger point is the trailing edge.

Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width

Pulse Width Range 20ns ~ 10s

Slope Trigger

Slope Trigger Mode Trigger when (< , > , = , or ? ); Positive slope or Negative slope

Slope Trigger Point Equal: The oscilloscope triggers when the waveform slope is equal to the set slope.

Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.

Less than: The oscilloscope triggers when the waveform slope is less than the set slope.

Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.

Time Range 20ns ~ 10s

Overtime Trigger

Over Time Mode Rising edge or Falling edge

Time Range 20ns ~ 10s

Alternative Trigger

Trigger on CH1 Internal Trigger: Edge, Pulse Width, Video, Slope

Trigger on CH2 Internal Trigger: Edge, Pulse Width, Video, Slope

Trigger Frequency Counter

Readout Resolution 6 digits

Accuracy (typical) 30ppm (including all frequency reference errors and 1 count errors)

Frequency Range AC coupled, from 4Hz minimum to rated bandwidth

Signal Source Pulse Width or Edge Trigger modes: all available trigger sources

The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed.

Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time.

Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity.

Video Trigger mode: The Frequency Counter does not work.

Measure

Cursor Measurement Voltage difference between cursors: ?V

Time difference between cursors: ?T

Reciprocal of ?T in Hertz (1/?T)

Auto Measuerment Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time,

+Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid,

Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH,

FRF, FFR, LRR, LRF, LFR, LFF

Signal Source Mode

Waveform Impedance DC-25MHz

Sample Rate 200MHzDDS

Output Waveform Arbitrary wave/square wave/sine wave/triangle wave/trapezoidal wave/pulse wave/DC

Frequency Resolution 0.1%

Waveform Depth 2KSa

Vertical Resolution 12bit

Frequency Stability <30ppm

Waveform Range -3.5V~+3.5V

Output Impedance 50O

Output Current 50mA Ipeak=100mA

System BW 25M

Harmonic Distortion -50dBc(1KHz),-40dBc(10KHz)

General Features

Display

Display Type 7 inch 64K color TFT (diagonal liquid crystal)

Display Resolution 800 horizontal by 480 vertical pixels

Display Contrast Adjustable (16 gears) with the progress bar

Probe Compensator Output

Output Voltage( typical) About 5Vpp into =1MO load

Frequency(typical) 1kHz

Power Supply

Supply Voltage 100-120VACRMS(10%), 45Hz to 440Hz, CAT?

120-240VACRMS(10%), 45Hz to 66Hz, CAT?

Power Consumption <30W

Fuse 2A, T rating, 250V

Environmental

Temperature Operating: 32? to 122? (0? to 50?);

Nonoperating: -40? to 159.8? (-40? to +71?)

Cooling Method Convection

Humidity +104? or below (+40? or below): =90% relative humidity;

106? to 122? (+41? to 50?): =60% relative humidity

Altitude Operating: Below 3,000m (10,000 feet);

Nonoperaring: Below 15,000m(50,000 feet)

Mechanical

Size Length 385mm, Width 200mm, Height 245mm

Weight 3.5KG(with Packing); 2.08KG(without Packing)

Package List:

1 x Digital Storage Oscilloscope

2 x Probes

1 x Oscilloscope Power line

1 x Hantek data CD

1 x USB line

1 x Manufacturer Certificate

CH004113

No customer reviews for the moment.

Write your review

Hantek DSO4204C Digital Oscilloscope 200MHz 4Channels Bandwidth 1GSas Waveform Generator

Hantek DSO4204C Digital Oscilloscope 200MHz 4Channels Bandwidth 1GSa/s Waveform Generator

Write your review

16 other products in the same category